From bd508a509c2ac47b9bfe5ad8719fafa8576e56a6 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Sat, 2 Jan 2021 12:59:40 +0800 Subject: [PATCH] arm64: dts: qcom: c630: keep both touchpad devices enabled [ Upstream commit a9164910c5ceed63551280a4a0b85d37ac2b19a5 ] Indicated by AML code in ACPI table, the touchpad in-use could be found on two possible slave addresses on &i2c3, i.e. hid@15 and hid@2c. And which one is in-use can be determined by reading another address on the I2C bus. Unfortunately, for DT boot, there is currently no support in firmware to make this check and patch DT accordingly. This results in a non-functional touchpad on those C630 devices with hid@2c. As i2c-hid driver will stop probing the device if there is nothing on the slave address, we can actually keep both devices enabled in DT, and i2c-hid driver will only probe the existing one. The only problem is that we cannot set up pinctrl in both device nodes, as two devices with the same pinctrl will cause pin conflict that makes the second device fail to probe. Let's move the pinctrl state up to parent node to solve this problem. As the pinctrl state of parent node is already defined in sdm845.dtsi, it ends up with overwriting pinctrl-0 with i2c3_hid_active state added in there. Fixes: 11d0e4f28156 ("arm64: dts: qcom: c630: Polish i2c-hid devices") Signed-off-by: Shawn Guo Link: https://lore.kernel.org/r/20210102045940.26874-1-shawn.guo@linaro.org Signed-off-by: Bjorn Andersson Signed-off-by: Sasha Levin --- arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts | 10 ++-------- 1 file changed, 2 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts index 76a8c996d497..d70aae77a6e8 100644 --- a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts +++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts @@ -263,6 +263,8 @@ &i2c3 { status = "okay"; clock-frequency = <400000>; + /* Overwrite pinctrl-0 from sdm845.dtsi */ + pinctrl-0 = <&qup_i2c3_default &i2c3_hid_active>; tsel: hid@15 { compatible = "hid-over-i2c"; @@ -270,9 +272,6 @@ hid-descr-addr = <0x1>; interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>; - - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_hid_active>; }; tsc2: hid@2c { @@ -281,11 +280,6 @@ hid-descr-addr = <0x20>; interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>; - - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_hid_active>; - - status = "disabled"; }; }; -- 2.17.1