git.somdevices.com Git - linux.git/log

iio: proximity: sx9500: claim direct mode during raw proximity reads

[ Upstream commit 6b2e7589b82ff534dd5c6d67dd83c53f13691bec ]

Driver was checking for direct mode but not locking it. Use the
claim/release helper functions to guarantee the device stays in
direct mode during raw reads of proximity data.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Vlad Dogaru <ddvlad@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: magnetometer: mag3110: claim direct mode during raw writes

[ Upstream commit 80dea21f95a4672cce545f48dc2ca500b69a2584 ]

Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw writes.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: pressure: ms5611: claim direct mode during oversampling changes

[ Upstream commit 3bc1abcddb24f55b9c251e03caa4f9bd22ff748b ]

Driver was checking for direct mode before changing oversampling
ratios, but was not locking it. Use the claim/release helper
functions to guarantee the device stays in direct mode while the
oversampling ratios are being updated. Continue to use the drivers
private state lock to protect against conflicting direct mode access
of the state data.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: trigger: free trigger resource correctly

[ Upstream commit 10e840dfb0b7fc345082dd9e5fff3c1c02e7690e ]

These stand-alone trigger drivers were using iio_trigger_put()
where they should have been using iio_trigger_free(). The
iio_trigger_put() adds a module_put which is bad since they
never did a module_get.

In the sysfs driver, module_get/put's are used as triggers are
added & removed. This extra module_put() occurs on an error path
in the probe routine (probably rare).

In the bfin-timer & interrupt trigger drivers, the module resources
are not explicitly managed, so it's doing a put on something that
was never get'd. It occurs on the probe error path and on the
remove path (not so rare).

Tested with the sysfs trigger driver.
The bfin & interrupt drivers were build tested & inspected only.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: mali-dp: fix Lx_CONTROL register fields clobber

[ Upstream commit c7ffa59cf03c38b91d6ef01e42c1b52fd7a4f285 ]

When updating the rotation fields, one of the assignments zeroes out the
rest of the register fields, which include settings for chroma siting,
inverse gamma, AMBA AXI caching, and alpha blending.

Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: vmx - disable preemption to enable vsx in aes_ctr.c

[ Upstream commit 7dede913fc2ab9c0d3bff3a49e26fa9e858b0c13 ]

Some preemptible check warnings were reported from enable_kernel_vsx(). This
patch disables preemption in aes_ctr.c before enabling vsx, and they are now
consistent with other files in the same directory.

Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dma-mapping: Only swizzle DMA ops for IOMMU_DOMAIN_DMA

[ Upstream commit 4a8d8a14c0d08c2437cb80c05e88f6cc1ca3fb2c ]

The arm64 DMA-mapping implementation sets the DMA ops to the IOMMU DMA
ops if we detect that an IOMMU is present for the master and the DMA
ranges are valid.

In the case when the IOMMU domain for the device is not of type
IOMMU_DOMAIN_DMA, then we have no business swizzling the ops, since
we're not in control of the underlying address space. This patch leaves
the DMA ops alone for masters attached to non-DMA IOMMU domains.

Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6

[ Upstream commit 4cd6a59f5c1a9b0cca0da09fbba42b9450ffc899 ]

We have more than four uarts on some SoCs and that can cause
noise with errors while booting.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxl: Force psl data-cache flush during device shutdown

[ Upstream commit d7b1946c7925a270062b2e0718aa57b42ba619c0 ]

This change adds a force psl data cache flush during device shutdown
callback. This should reduce a possibility of psl holding a dirty
cache line while the CAPP is being reinitialized, which may result in
a UE [load/store] machine check error.

Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/corenet: explicitly disable the SDHC controller on kmcoge4

[ Upstream commit a674c7d470bb47e82f4eb1fa944eadeac2f6bbaf ]

It is not implemented on the kmcoge4 hardware and if not disabled it
leads to error messages with the corenet32_smp_defconfig.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: baytrail: Fix debugfs offset output

[ Upstream commit 3655a1ca6bd8e7300f2bb196208d5139aa6b2eda ]

Apparently each GPIO pad's register are 16 bytes, so multiply the pad_map
by that. The same is done in byt_gpio_reg the only other place where
pad_map is used.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/arm-smmu-v3: Clear prior settings when updating STEs

[ Upstream commit 810871c57011eb3e89e6768932757f169d666cd2 ]

To prevent corruption of the stage-1 context pointer field when
updating STEs, rebuild the entire containing dword instead of
clearing individual fields.

Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book 3S: XICS: correct the real mode ICP rejecting counter

[ Upstream commit 37451bc95dee0e666927d6ffdda302dbbaaae6fa ]

Some counters are added in Commit 6e0365b78273 ("KVM: PPC: Book3S HV:
Add ICP real mode counters"), to provide some performance statistics to
determine whether further optimizing is needed for real mode functions.

The n_reject counter counts how many times ICP rejects an irq because of
priority in real mode. The redelivery of an lsi that is still asserted
after eoi doesn't fall into this category, so the increasement there is
removed.

Also, it needs to be increased in icp_rm_deliver_irq() if it rejects
another one.

Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: drm_minor_register(): Clean up debugfs on failure

[ Upstream commit a67834f8bfa1e2f48bb27d07b9a552ba7c3af82a ]

Call drm_debugfs_cleanup() in case drm_debugfs_init() fails to
cover for failure in the drm_driver.debugfs_init callback.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-3-noralf@tronnes.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: samsung: exynos5433: Add IDs for PHYCLK_MIPIDPHY0_* clocks

[ Upstream commit 5ccb58968bf7f46dbd128df88f71838a5a9750b8 ]

Add missing identifiers for phyclk_mipidphy0_bitclkdiv8_phy and
phyclk_mipidphy0_rxclkesc0_phy clocks. Access to those clocks is needed
to setup initial clock configuration for display subsystem in device tree
in order to avoid dependency on the configuration left by the bootloader.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / OPP: Error out on failing to add static OPPs for v1 bindings

[ Upstream commit 04a86a84c42ca18f37ab446127dc619b41dd3b23 ]

The code adding static OPPs for V2 bindings already does so. Make the V1
bindings specific code behave the same.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EDAC, amd64: Add x86cpuid sanity check during init

[ Upstream commit 1bd9900b8301fc505f032c90ea487824cf824e99 ]

Match one of the devices in amd64_cpuids[] before loading the module.
This is an additional sanity check against users trying to load
amd64_edac_mod on unsupported systems.

Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1485537863-2707-9-git-send-email-Yazen.Ghannam@amd.com
[ Get rid of err_ret label, make it a bit more readable this way. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: clockgen: Add compatible string for LS1012A

[ Upstream commit 73447f68d7b2bc1df870da88b0e21d2bc1afc025 ]

Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: imx53-qsb-common: fix FEC pinmux config

[ Upstream commit 8b649e426336d7d4800ff9c82858328f4215ba01 ]

The pinmux configuration in device tree was different from manual
muxing in <u-boot>/board/freescale/mx53loco/mx53loco.c
All pins were configured as NO_PAD_CTL(1 << 31), which was fine as the
bootloader already did the correct pinmuxing for us.
But recently u-boot is migrating to reuse device tree files from the
kernel tree, so it seems to be better to have the correct pinmuxing in
our files, too.

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/netback: set default upper limit of tx/rx queues to 8

[ Upstream commit 56dd5af9bc23d0d5d23bb207c477715b4c2216c5 ]

The default for the maximum number of tx/rx queues of one interface is
the number of cpus of the system today. As each queue pair reserves 512
grant pages this default consumes a ridiculous number of grants for
large guests.

Limit the queue number to 8 as default. This value can be modified
via a module parameter if required.

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/core: Add missing update_rq_clock() call in sched_move_task()

[ Upstream commit 1b1d62254df0fe42a711eb71948f915918987790 ]

Bug was noticed via this warning:

  WARNING: CPU: 6 PID: 1 at kernel/sched/sched.h:804 detach_task_cfs_rq+0x8e8/0xb80
  rq->clock_update_flags < RQCF_ACT_SKIP
  Modules linked in:
  CPU: 6 PID: 1 Comm: systemd Not tainted 4.10.0-rc5-00140-g0874170baf55-dirty #1
  Hardware name: Supermicro SYS-4048B-TRFT/X10QBi, BIOS 1.0 04/11/2014
  Call Trace:
   dump_stack+0x4d/0x65
   __warn+0xcb/0xf0
   warn_slowpath_fmt+0x5f/0x80
   detach_task_cfs_rq+0x8e8/0xb80
   ? allocate_cgrp_cset_links+0x59/0x80
   task_change_group_fair+0x27/0x150
   sched_change_group+0x48/0xf0
   sched_move_task+0x53/0x150
   cpu_cgroup_attach+0x36/0x70
   cgroup_taskset_migrate+0x175/0x300
   cgroup_migrate+0xab/0xd0
   cgroup_attach_task+0xf0/0x190
   __cgroup_procs_write+0x1ed/0x2f0
   cgroup_procs_write+0x14/0x20
   cgroup_file_write+0x3f/0x100
   kernfs_fop_write+0x104/0x180
   __vfs_write+0x37/0x140
   vfs_write+0xb8/0x1b0
   SyS_write+0x55/0xc0
   do_syscall_64+0x61/0x170
   entry_SYSCALL64_slow_path+0x25/0x25

Reported-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: mvebu: Handle changes to the bridge windows while enabled

[ Upstream commit d9bf28e2650fe3eeefed7e34841aea07d10c6543 ]

The PCI core will write to the bridge window config multiple times while
they are enabled.  This can lead to mbus failures like this:

mvebu_mbus: cannot add window '4:e8', conflicts with another window
mvebu-pcie mbus:pex@e0000000: Could not create MBus window at [mem 0xe0000000-0xe00fffff]: -22

For me this is happening during a hotplug cycle.  The PCI core is not
changing the values, just writing them twice while active.

The patch addresses the general case of any change to an active window, but
not atomically.  The code is slightly refactored so io and mem can share
more of the window logic.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

video: fbdev: pmag-ba-fb: Remove bad `__init' annotation

[ Upstream commit 879e5a0df626f39cbb3c61bb90373e56d67012c4 ]

Fix:

WARNING: drivers/video/fbdev/pmag-ba-fb.o(.text+0x308): Section mismatch in reference from the function pmagbafb_probe() to the function .init.text:pmagbafb_erase_cursor()
The function pmagbafb_probe()
references the function __init pmagbafb_erase_cursor().
This is often because pmagbafb_probe lacks a __init
annotation or the annotation of pmagbafb_erase_cursor is wrong.

-- a fallout from a missed update from commit 9625b51350cc ("VIDEO:
PMAG-BA: Fix section mismatch") and then commit 48c68c4f1b54 ("Drivers:
video: remove __dev* attributes.")

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

adv7604: Initialize drive strength to default when using DT

[ Upstream commit da8892d410db224d9a24104529794e6e37e0c100 ]

The adv7604 driver platform data contains fields for configuring the drive
strength of the output pins. When probing the driver through DT these
fields are not explicitly initialized, which means they are left at 0. This
is a reserved setting for the drive strength configuration though and can
cause signal integrity issues.

Whether these signal integrity issues are visible depends on the PCB
specifics (e.g. the higher the load capacitance for the output the more
visible the issue). But it has been observed on existing solutions at high
pixel clock rates.

Initialize the drive strength settings to the power-on-reset value of the
device when probing through devicetree to avoid this issue.

Fixes: 0e158be0162b ("adv7604: Add DT support")

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: mvebu: pl310-cache disable double-linefill

commit cda80a82ac3e89309706c027ada6ab232be1d640 upstream.

Under heavy system stress mvebu SoC using Cortex A9 sporadically
encountered instability issues.

The "double linefill" feature of L2 cache was identified as causing
dependency between read and write which lead to the deadlock.

Especially, it was the cause of deadlock seen under heavy PCIe traffic,
as this dependency violates PCIE overtaking rule.

Fixes: c8f5a878e554 ("ARM: mvebu: use DT properties to fine-tune the L2 configuration")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
[gregory.clement@free-electrons.com: reformulate commit log, add Armada
375 and add Fixes tag]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: r8712u: Fix Sparse warning in rtl871x_xmit.c

[ Upstream commit 07222e535831b916221dd2a48a3047ec7e45dc72 ]

Sparse reports the following:
  CHECK   drivers/staging/rtl8712/rtl871x_xmit.c
drivers/staging/rtl8712/rtl871x_xmit.c:350:44: warning: restricted __le32 degrades to integer
drivers/staging/rtl8712/rtl871x_xmit.c:491:23: warning: incorrect type in initializer (different base types)
drivers/staging/rtl8712/rtl871x_xmit.c:491:23:    expected unsigned short [usertype] *fctrl
drivers/staging/rtl8712/rtl871x_xmit.c:491:23:    got restricted __le16 *<noident>
drivers/staging/rtl8712/rtl871x_xmit.c:580:36: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8712/rtl871x_xmit.c:580:36:    expected unsigned short [unsigned] [short] [usertype] <noident>
drivers/staging/rtl8712/rtl871x_xmit.c:580:36:    got restricted __be16 [usertype] <noident>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: don't print error message in case of missing Xenstore entry

[ Upstream commit 4e93b6481c87ea5afde944a32b4908357ec58992 ]

When registering for the Xenstore watch of the node control/sysrq the
handler will be called at once. Don't issue an error message if the
Xenstore node isn't there, as it will be created only when an event
is being triggered.

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64: Don't try to use radix MMU under a hypervisor

[ Upstream commit 18569c1f134e1c5c88228f043c09678ae6052b7c ]

Currently, if the kernel is running on a POWER9 processor under a
hypervisor, it will try to use the radix MMU even though it doesn't have
the necessary code to use radix under a hypervisor (it doesn't negotiate
use of radix, and it doesn't do the H_REGISTER_PROC_TBL hcall). The
result is that the guest kernel will crash when it tries to turn on the
MMU.

This fixes it by looking for the /chosen/ibm,architecture-vec-5
property, and if it exists, clears the radix MMU feature bit, before we
decide whether to initialize for radix or HPT. This property is created
by the hypervisor as a result of the guest calling the
ibm,client-architecture-support method to indicate its capabilities, so
it will indicate whether the hypervisor agreed to us using radix.

Systems without a hypervisor may have this property also (for example,
skiboot creates it), so we check the HV bit in the MSR to see whether we
are running as a guest or not. If we are in hypervisor mode, then we can
do whatever we like including using the radix MMU.

The reason for using this property is that in future, when we have
support for using radix under a hypervisor, we will need to check this
property to see whether the hypervisor agreed to us using radix.

Fixes: 2bfd65e45e87 ("powerpc/mm/radix: Add radix callbacks for early init routines")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Avoid possible deadlock on pci_lock and p->pi_lock

[ Upstream commit cdcb33f9824429a926b971bf041a6cec238f91ff ]

pci_lock is an IRQ-safe spinlock that protects all accesses to PCI
configuration space (see PCI_OP_READ() and PCI_OP_WRITE() in pci/access.c).

The pci_cfg_access_unlock() path acquires pci_lock, then p->pi_lock (inside
wake_up_all()). According to lockdep, there is a possible path involving
snbep_uncore_pci_read_counter() that could acquire them in the reverse
order: acquiring p->pi_lock, then pci_lock, which could result in a
deadlock. Lockdep details are in the bugzilla below.

Avoid the possible deadlock by dropping pci_lock before waking up any
config access waiters.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=192901
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/exynos: g2d: prevent integer overflow in

[ Upstream commit e41456bfc811f12b5dcda6f2d6849bdff68f6c0a ]

The size computations done in the ioctl function use an integer.
If userspace submits a request with req->cmd_nr or req->cmd_buf_nr
set to INT_MAX, the integer computations overflow later, leading
to potential (kernel) memory corruption.

Prevent this issue by enforcing a limit on the number of submitted
commands, so that we have enough headroom later for the size
computations.

Note that this change has no impact on the currently available
users in userspace, like e.g. libdrm/exynos.

While at it, also make a comment about the size computation more
detailed.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bt8xx: fix memory leak

[ Upstream commit 6792eb0cf9310ec240b7e7c9bfa86dff4c758c68 ]

If dvb_attach() fails then we were just printing an error message and
exiting but the memory allocated to state was not released.

Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/crypto: Extend key length check for AES-XTS in fips mode.

[ Upstream commit a4f2779ecf2f42b0997fedef6fd20a931c40a3e3 ]

In fips mode only xts keys with 128 bit or 125 bit are allowed.
This fix extends the xts_aes_set_key function to check for these
valid key lengths in fips mode.

Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/prng: Adjust generation of entropy to produce real 256 bits.

[ Upstream commit d34b1acb78af41b8b8d5c60972b6555ea19f7564 ]

The generate_entropy function used a sha256 for compacting
together 256 bits of entropy into 32 bytes hash. However, it
is questionable if a sha256 can really be used here, as
potential collisions may reduce the max entropy fitting into
a 32 byte hash value. So this batch introduces the use of
sha512 instead and the required buffer adjustments for the
calling functions.

Further more the working buffer for the generate_entropy
function has been widened from one page to two pages. So now
1024 stckf invocations are used to gather 256 bits of
entropy. This has been done to be on the save side if the
jitters of stckf values isn't as good as supposed.

Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/dasd: check for device error pointer within state change interrupts

[ Upstream commit 2202134e48a3b50320aeb9e3dd1186833e9d7e66 ]

Check if the device pointer is valid. Just a sanity check since we already
are in the int handler of the device.

Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mei: return error on notification request to a disconnected client

[ Upstream commit 7c47d2ca0feca767479329da23523ed798acb854 ]

Request for a notification from a disconnected client will be ignored
silently by the FW but the caller should know that the operation hasn't
succeeded.

Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

exynos4-is: fimc-is: Unmap region obtained by of_iomap()

[ Upstream commit 4742575cde1f3cee0ea6b41af42781672315b04b ]

Free memory mapping, if fimc_is_probe is not successful.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: boards: remove .pm_ops in all Atom/DPCM machine drivers

[ Upstream commit 3639ac1cd5177685a5c8abb7230096b680e1d497 ]

This patch corrects an omission in bytcr_rt5640 and bytcr_rt5651.
All existing machine drivers shall not use .pm_ops to avoid a double
suspend, as initially implemented by 3f2dcbeaeb2b
("ASoC: Intel: Remove soc pm handling to allow platform driver handle it").

Reported-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfs: open() with O_CREAT should not create inodes with unknown ids

[ Upstream commit 1328c727004d432bbdfba0ffa02a166df04c7305 ]

may_create() rejects creation of inodes with ids which lack a
mapping into s_user_ns. However for O_CREAT may_o_create() is
is used instead. Add a similar check there.

Fixes: 036d523641c6 ("vfs: Don't create inodes with a uid or gid unknown to the vfs")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

brcmfmac: check brcmf_bus_get_memdump result for error

[ Upstream commit f4737a62033d7f3e0db740c449fc62119da7ab8a ]

This method may be unsupported (see: USB bus) or may just fail (see:
SDIO bus).
While at it rework logic in brcmf_sdio_bus_get_memdump function to avoid
too many conditional code nesting levels.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: lmv: Error not handled for lmv_find_target

[ Upstream commit 30af99db7ab3483f5ce83ccb890533c9378c2ced ]

This issue is found by smatch; has been reported as-
Unchecked usage of potential ERR_PTR result in lmv_hsm_req_count
and lmv_hsm_req_build. Added ERR_PTR in both functions and also
return value check added.

Signed-off-by: Ulka Vaze <ulka.vaze@yahoo.in>
Signed-off-by: Aditya Pandit <panditadityashreesh@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6523
Reviewed-on: http://review.whamcloud.com/14918
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: ptlrpc: skip lock if export failed

[ Upstream commit 4c43c27ddc461d8473cedd70f2549614641dfbc7 ]

This patch resolves IO vs eviction race.
After eviction failed export stayed at stale list,
a client had IO processing and reconnected during it.
A client sent brw rpc with last lock cookie and new connection.
The lock with failed export was found and assert was happened.
(ost_handler.c:1812:ost_prolong_lock_one())
  ASSERTION( lock->l_export == opd->opd_exp ) failed:

1. Skip the lock at ldlm_handle2lock if lock export failed.
2. Validation of lock for IO was added at hpreq_check(). The lock
    searching is based on granted interval tree. If server doesn`t
    have a valid lock, it reply to client with ESTALE.

Signed-off-by: Alexander Boyko <alexander.boyko@seagate.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7702
Seagate-bug-id: MRP-2787
Reviewed-on: http://review.whamcloud.com/18120
Reviewed-by: Fan Yong <fan.yong@intel.com>
Reviewed-by: Vitaly Fertman <vitaly.fertman@seagate.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: hsm: stack overrun in hai_dump_data_field

[ Upstream commit 22aadb91c0a0055935109c175f5446abfb130702 ]

The function hai_dump_data_field will do a stack buffer
overrun when cat'ing /sys/fs/lustre/.../hsm/actions if an action has
some data in it.

hai_dump_data_field uses snprintf. But there is no check for
truncation, and the value returned by snprintf is used as-is. The
coordinator code calls hai_dump_data_field with 12 bytes in the
buffer. The 6th byte of data is printed incompletely to make room for
the terminating NUL. However snprintf still returns 2, so when
hai_dump_data_field writes the final NUL, it does it outside the
reserved buffer, in the 13th byte of the buffer. This stack buffer
overrun hangs my VM.

Fix by checking that there is enough room for the next 2 characters
plus the NUL terminator. Don't print half bytes. Change the format to
02X instead of .2X, which makes more sense.

Signed-off-by: frank zago <fzago@cray.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8171
Reviewed-on: http://review.whamcloud.com/20338
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Jean-Baptiste Riaux <riaux.jb@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: llite: don't invoke direct_IO for the EOF case

[ Upstream commit 77759771fb95420d23876cb104ab65c022613325 ]

The function generic_file_read_iter() does not check EOF
before invoke direct_IO callback. So we have to check it
ourselves.

Signed-off-by: Yang Sheng <yang.sheng@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8969
Reviewed-on: https://review.whamcloud.com/24552
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: intel_mid_thermal: Fix module autoload

[ Upstream commit a93151a72061e944a4915458b1b1d6d505c03bbf ]

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/platform/x86/intel_mid_thermal.ko | grep alias
$

After this patch:

$ modinfo drivers/platform/x86/intel_mid_thermal.ko | grep alias
alias: platform:msic_thermal

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: aacraid: Process Error for response I/O

[ Upstream commit 4ec57fb4edaec523f0f78a0449a3b063749ac58b ]

Make sure that the driver processes error conditions even in the fast
response path for response from the adapter.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Dave Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/manage: correct return value check on xenbus_scanf()

[ Upstream commit 4fed1b125eb6252bde478665fc05d4819f774fa8 ]

A negative return value indicates an error; in fact the function at
present won't ever return zero.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error

[ Upstream commit e8e1a5b5679b1ae1ff03a3883b011b84e7226171 ]

This driver now using devm_regmap_init/devm_regmap_init_i2c, so it needs
to select REGMAP/REGMAP_I2C accordingly.

Fixes: ("3d84fdb3f0b5 gpio: mcp23s08: use regmap")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: nand: sunxi: Fix the non-polling case in sunxi_nfc_wait_events()

[ Upstream commit 19649e2c16fbc94b664f7074ec4fa9f15292fdce ]

wait_for_completion_timeout() returns 0 if a timeout occurred, 1
otherwise. Fix the sunxi_nfc_wait_events() accordingly.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: sunxi-ng: Check kzalloc() for errors and cleanup error path

[ Upstream commit 5d806f9fc8e63d7a44e0fd1ef26a7c27efae0e51 ]

This kzalloc() could fail. Let's bail out with -ENOMEM here
instead of NULL dereferencing. That silences static checkers. We
should also cleanup on the error path even though this function
returning an error probably means the system won't boot.

Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: fix reading sram contents for QCA4019

[ Upstream commit 7f622593cc5add77a99cd39404e8a851be9de792 ]

With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.

While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.

Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cx231xx: Fix I2C on Internal Master 3 Bus

[ Upstream commit 6c5da8031a3abfad259190d35f83d89568b72ee2 ]

Internal Master 3 Bus can send and receive only 4 bytes per time.

Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: dp83867: Recover from "port mirroring" N/A MODE4

[ Upstream commit ac6e058b75be71208e98a5808453aae9a17be480 ]

The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.

To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).

To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.

Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"

https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clocksource/drivers/arm_arch_timer: Add dt binding for hisilicon-161010101 erratum

[ Upstream commit 729e55225b1f6225ee7a2a358d5141a3264627c4 ]

This erratum describes a bug in logic outside the core, so MIDR can't be
used to identify its presence, and reading an SoC-specific revision
register from common arch timer code would be awkward. So, describe it
in the device tree.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/fsl-dcu: check for clk_prepare_enable() error

[ Upstream commit ef15d36154cc741d7ded4ae4fa0cf7987354e313 ]

clk_prepare_enable() may fail, so we should better check its return
value.

Also place the of_node_put() function right after clk_prepare_enable(),
in order to avoid calling of_node_put() twice in case clk_prepare_enable()
fails.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: use the PROBE_RESP_QUEUE to send deauth to unknown station

[ Upstream commit d45cb20e123c5d7d6cd56301bc98f0bfd725cd77 ]

When we send a deauth to a station we don't know about, we
need to use the PROBE_RESP queue. This can happen when we
send a deauth to a station that is not associated to us.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf tools: Only increase index if perf_evsel__new_idx() succeeds

[ Upstream commit 75fc5ae5cc53fff71041ecadeb3354a2b4c9fe42 ]

Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1485952447-7013-2-git-send-email-treeze.taeung@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: when dpm disabled, also need to stop/start vce.

[ Upstream commit 28ed5504ab4b211a4e589e648e5ebd1e0caa7a6a ]

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: riic: correctly finish transfers

[ Upstream commit 71ccea095ea1d4efd004dab971be6d599e06fc3f ]

This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.

At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.

Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.

This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.

Fixes: 310c18a41450 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/ena: change driver's default timeouts

[ Upstream commit 7102a18ac3f323805e3cd8f3dc64907644608c1e ]

The timeouts were too agressive and sometimes cause false alarms.

Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: do not use stripe_width if it is not set

[ Upstream commit 5469d7c3087ecaf760f54b447f11af6061b7c897 ]

Avoid using stripe_width for sbi->s_stripe value if it is not actually
set. It prevents using the stride for sbi->s_stripe.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix stripe-unaligned allocations

[ Upstream commit d9b22cf9f5466a057f2a4f1e642b469fa9d73117 ]

When a filesystem is created using:

mkfs.ext4 -b 4096 -E stride=512 <dev>

and we try to allocate 64MB extent, we will end up directly in
ext4_mb_complex_scan_group(). This is because the request is detected
as power-of-two allocation (so we start in ext4_mb_regular_allocator()
with ac_criteria == 0) however the check before
ext4_mb_simple_scan_group() refuses the direct buddy scan because the
allocation request is too large. Since cr == 0, the check whether we
should use ext4_mb_scan_aligned() fails as well and we fall back to
ext4_mb_complex_scan_group().

Fix the problem by checking for upper limit on power-of-two requests
directly when detecting them.

Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mvneta: fix build errors when linux/phy*.h is removed from net/dsa.h

[ Upstream commit 9303ab2b3402b60f6c39abfdbfa4ce00fce8bee4 ]

drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]

Add linux/phy_fixed.h to mvneta.c

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/MSI: Return failure when msix_setup_entries() fails

[ Upstream commit 3adfb572f2978a980b250a9e1a56f84f3a031001 ]

If alloc_msi_entry() fails, we free resources and set ret = -ENOMEM.

However, msix_setup_entries() returns 0 unconditionally. Return the error
code instead.

Fixes: e75eafb9b039 ("genirq/msi: Switch to new irq spreading infrastructure")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712u: Fix endian settings for structs describing network packets

[ Upstream commit 221c46d28957bd6e2158abc2179ce4a8c9ce07d3 ]

The headers describing a number of network packets do not have the
correct endian settings for several types of data.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Added PCI IDs for BCM57452 and BCM57454 ASICs

[ Upstream commit 32b40798c1b40343641f04cdfd09652af70ea0e9 ]

Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mfd: axp20x: Fix axp288 PEK_DBR and PEK_DBF irqs being swapped

[ Upstream commit 1af468ebe45591651ec3bafc2e9ddc6fdef70ae0 ]

The R in PEK_DBR stands for rising, so it should be mapped to
AXP288_IRQ_POKP where the last P stands for positive edge.

Likewise PEK_DBF should be mapped to the falling edge, aka the
_N_egative edge, so it should be mapped to AXP288_IRQ_POKN.

This fixes the inverted powerbutton status reporting by the
axp20x-pek driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mfd: ab8500-sysctrl: Handle probe deferral

[ Upstream commit 7e9c40c63933a643908d686bd89dfc2315e8c70a ]

In the current boot, clients making use of the AB8500 sysctrl
may be probed before the ab8500-sysctrl driver. This gives them
-EINVAL, but should rather give -EPROBE_DEFER.

Before this, the abx500 clock driver didn't probe properly,
and as a result the codec driver in turn using the clocks did
not probe properly. After this patch, everything probes
properly.

Also add OF compatible-string probing. This driver is all
device tree, so let's just make a drive-by-fix of that as
well.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: s3cmci: include linux/interrupt.h for tasklet_struct

[ Upstream commit e1c6ec26b853e9062f0b3daaf695c546d0702953 ]

I got this new build error on today's linux-next

drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]

While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool

[ Upstream commit 1d6dbd1752fb4347a4a5db06c8f5cd35dd1919f4 ]

FIX - firmware wants non-RW SYS PD IOs to avoid FastPath for better
tracking and other functionalities if the device is task management
capable.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / wakeirq: report a wakeup_event on dedicated wekup irq

[ Upstream commit 09bb6e93956ae5175b96905b723ec879c3ca0765 ]

There are two reasons for reporting wakeup event when dedicated wakeup
IRQ is triggered:

- wakeup events accounting, so proper statistical data will be
  displayed in sysfs and debugfs;

- there are small window when System is entering suspend during which
  dedicated wakeup IRQ can be lost:

dpm_suspend_noirq()
  |- device_wakeup_arm_wake_irqs()
      |- dev_pm_arm_wake_irq(X)
         |- IRQ is enabled and marked as wakeup source
[1]...
  |- suspend_device_irqs()
     |- suspend_device_irq(X)
|- irqd_set(X, IRQD_WAKEUP_ARMED);
   |- wakup IRQ armed

The wakeup IRQ can be lost if it's triggered at point [1]
and not armed yet.

Hence, fix above cases by adding simple pm_wakeup_event() call in
handle_threaded_wake_irq().

Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
[ tony@atomide.com: added missing return to avoid warnings ]
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Assign DSCP for R-RoCE QPs Address Path

[ Upstream commit ed88451e1f2d400fd6a743d0a481631cf9f97550 ]

For Routable RoCE QPs, the DSCP should be set in the QP's
address path.

The DSCP's value is derived from the traffic class.

Fixes: 2811ba51b049 ("IB/mlx5: Add RoCE fields to Address Vector")
Cc: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: fsl-mc: Add missing header

[ Upstream commit 07e9ef146071adf316312b3dd4abfe41c9a45a7d ]

Compiling the fsl-mc bus driver will yield a couple of static analysis
errors:
warning: symbol 'fsl_mc_msi_domain_alloc_irqs' was not declared
warning: symbol 'fsl_mc_msi_domain_free_irqs' was not declared.
warning: symbol 'its_fsl_mc_msi_init' was not declared.
warning: symbol 'its_fsl_mc_msi_cleanup' was not declared.

Since these are properly declared, but the header is not included, add
it in the source files. This way the symbol is properly exported.

Signed-off-by: Bogdan Purcareata <bogdan.purcareata@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: ccp - Set the AES size field for all modes

[ Upstream commit f7cc02b3c3a33a10dd5bb9e5dfd22e47e09503a2 ]

Ensure that the size field is correctly populated for
all AES modes.

Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: Do not clear real_cpus mask on policy init

[ Upstream commit f451014692ae34e587b00de6745e16661cf734d8 ]

If new_policy is set in cpufreq_online(), the policy object has just
been created and its real_cpus mask has been zeroed on allocation,
and the driver's ->init() callback should not touch it.

It doesn't need to be cleared again, so don't do that.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix tracing sample code warning.

commit a0cb2b5c390151837b08e5f7bca4a6ecddbcd39c upstream.

Commit 6575257c60e1 ("tracing/samples: Fix creation and deletion of
simple_thread_fn creation") introduced a new warning due to using a
boolean as a counter.

Just make it "int".

Fixes: 6575257c60e1 ("tracing/samples: Fix creation and deletion of simple_thread_fn creation")
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing/samples: Fix creation and deletion of simple_thread_fn creation

commit 6575257c60e1a26a5319ccf2b5ce5b6449001017 upstream.

Commit 7496946a8 ("tracing: Add samples of DECLARE_EVENT_CLASS() and
DEFINE_EVENT()") added template examples for all the events. It created a
DEFINE_EVENT_FN() example which reused the foo_bar_reg and foo_bar_unreg
functions.

Enabling both the TRACE_EVENT_FN() and DEFINE_EVENT_FN() example trace
events caused the foo_bar_reg to be called twice, creating the test thread
twice. The foo_bar_unreg would remove it only once, even if it was called
multiple times, leaving a thread existing when the module is unloaded,
causing an oops.

Add a ref count and allow foo_bar_reg() and foo_bar_unreg() be called by
multiple trace events.

Fixes: 7496946a8 ("tracing: Add samples of DECLARE_EVENT_CLASS() and DEFINE_EVENT()")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/msm: fix an integer overflow test

commit 65e93108891e571f177c202add9288eda9ac4100 upstream.

We recently added an integer overflow check but it needs an additional
tweak to work properly on 32 bit systems.

The problem is that we're doing the right hand side of the assignment as
type unsigned long so the max it will have an integer overflow instead
of being larger than SIZE_MAX. That means the "sz > SIZE_MAX" condition
is never true even on 32 bit systems. We need to first cast it to u64
and then do the math.

Fixes: 4a630fadbb29 ("drm/msm: Fix potential buffer overflow issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/msm: Fix potential buffer overflow issue

commit 4a630fadbb29d9efaedb525f1a8f7449ad107641 upstream.

In function submit_create, if nr_cmds or nr_bos is assigned with
negative value, the allocated buffer may be small than intended.
Using this buffer will lead to buffer overflow issue.

Signed-off-by: Kasin Li <donglil@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/edp: read edp display control registers unconditionally

commit 7c838e2a9be5ab79b11c7f1520813bfdf0f45462 upstream.

Per my reading of the eDP spec, DP_DPCD_DISPLAY_CONTROL_CAPABLE bit in
DP_EDP_CONFIGURATION_CAP should be set if the eDP display control
registers starting at offset DP_EDP_DPCD_REV are "enabled". Currently we
check the bit before reading the registers, and DP_EDP_DPCD_REV is the
only way to detect eDP revision.

Turns out there are (likely buggy) displays that require eDP 1.4+
features, such as supported link rates and link rate select, but do not
have the bit set. Read the display control registers
unconditionally. They are supposed to read zero anyway if they are not
supported, so there should be no harm in this.

This fixes the referenced bug by enabling the eDP version check, and
thus reading of the supported link rates. The panel in question has 0 in
DP_MAX_LINK_RATE which is only supported in eDP 1.4+. Without the
supported link rates method we default to RBR which is insufficient for
the panel native mode. As a curiosity, the panel also has a bogus value
of 0x12 in DP_EDP_DPCD_REV, but that passes our check for >= DP_EDP_14
(which is 0x03).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103400
Reported-and-tested-by: Nicolas P. <issun.artiste@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171026142932.17737-1-jani.nikula@intel.com
(cherry picked from commit 0501a3b0eb01ac2209ef6fce76153e5d6b07034e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2: fstrim: Fix start offset of first cluster group during fstrim

commit 105ddc93f06ebe3e553f58563d11ed63dbcd59f0 upstream.

The first cluster group descriptor is not stored at the start of the
group but at an offset from the start.  We need to take this into
account while doing fstrim on the first cluster group.  Otherwise we
will wrongly start fstrim a few blocks after the desired start block and
the range can cross over into the next cluster group and zero out the
group descriptor there.  This can cause filesytem corruption that cannot
be fixed by fsck.

Link: http://lkml.kernel.org/r/1507835579-7308-1-git-send-email-ashish.samant@oracle.com
Signed-off-by: Ashish Samant <ashish.samant@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: return -ENOENT from uvd 6.0 early init for harvesting

commit cb4b02d7cac56a69d8137d8d843507cca9182aed upstream.

Fixes init failures on polaris cards with harvested UVD.

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8715/1: add a private asm/unaligned.h

commit 1cce91dfc8f7990ca3aea896bfb148f240b12860 upstream.

The asm-generic/unaligned.h header provides two different implementations
for accessing unaligned variables: the access_ok.h version used when
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set pretends that all pointers
are in fact aligned, while the le_struct.h version convinces gcc that the
alignment of a pointer is '1', to make it issue the correct load/store
instructions depending on the architecture flags.

On ARMv5 and older, we always use the second version, to let the compiler
use byte accesses. On ARMv6 and newer, we currently use the access_ok.h
version, so the compiler can use any instruction including stm/ldm and
ldrd/strd that will cause an alignment trap. This trap can significantly
impact performance when we have to do a lot of fixups and, worse, has
led to crashes in the LZ4 decompressor code that does not have a trap
handler.

This adds an ARM specific version of asm/unaligned.h that uses the
le_struct.h/be_struct.h implementation unconditionally. This should lead
to essentially the same code on ARMv6+ as before, with the exception of
using regular load/store instructions instead of the trapping instructions
multi-register variants.

The crash in the LZ4 decompressor code was probably introduced by the
patch replacing the LZ4 implementation, commit 4e1a33b105dd ("lib: update
LZ4 compressor module"), so linux-4.11 and higher would be affected most.
However, we probably want to have this backported to all older stable
kernels as well, to help with the performance issues.

There are two follow-ups that I think we should also work on, but not
backport to stable kernels, first to change the asm-generic version of
the header to remove the ARM special case, and second to review all
other uses of CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to see if they
might be affected by the same problem on ARM.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm/arm64: kvm: Disable branch profiling in HYP code

commit f9b269f3098121b5d54aaf822e0898c8ed1d3fec upstream.

When HYP code runs into branch profiling code, it attempts to jump to
unmapped memory, causing a HYP Panic.

Disable the branch profiling for code designed to run at HYP mode.

Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm/arm64: KVM: set right LR register value for 32 bit guest when inject abort

commit fd6c8c206fc5d0717b0433b191de0715122f33bb upstream.

When a exception is trapped to EL2, hardware uses  ELR_ELx to hold
the current fault instruction address. If KVM wants to inject a
abort to 32 bit guest, it needs to set the LR register for the
guest to emulate this abort happened in the guest. Because ARM32
architecture is pipelined execution, so the LR value has an offset to
the fault instruction address.

The offsets applied to Link value for exceptions as shown below,
which should be added for the ARM32 link register(LR).

Table taken from ARMv8 ARM DDI0487B-B, table G1-10:
Exception Offset, for PE state of:
A32   T32
Undefined Instruction +4   +2
Prefetch Abort +4   +4
Data Abort +8   +8
IRQ or FIQ +4   +4

  [ Removed unused variables in inject_abt to avoid compile warnings.
    -- Christoffer ]

Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Tested-by: Haibin Zhang <zhanghaibin7@huawei.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: ensure __dump_instr() checks addr_limit

commit 7a7003b1da010d2b0d1dc8bf21c10f5c73b389f1 upstream.

It's possible for a user to deliberately trigger __dump_instr with a
chosen kernel address.

Let's avoid problems resulting from this by using get_user() rather than
__get_user(), ensuring that we don't erroneously access kernel memory.

Where we use __dump_instr() on kernel text, we already switch to
KERNEL_DS, so this shouldn't adversely affect those cases.

Fixes: 60ffc30d5652810d ("arm64: Exception handling")
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: adau17x1: Workaround for noise bug in ADC

commit 1e6f4fc06f6411adf98bbbe7fcd79442cd2b2a75 upstream.

The ADC in the ADAU1361 (and possibly other Analog Devices codecs)
exhibits a cyclic variation in the noise floor (in our test setup between
-87 and -93 dB), a new value being attained within this range whenever a
new capture stream is started. The cycle repeats after about 10 or 11
restarts.

The workaround recommended by the manufacturer is to toggle the ADOSR bit
in the Converter Control 0 register each time a new capture stream is
started.

I have verified that the patch fixes this problem on the ADAU1361, and
according to the manufacturer toggling the bit in question in this manner
will at least have no detrimental effect on other chips served by this
driver.

Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: fix out-of-bounds read during ASN.1 parsing

commit 2eb9eabf1e868fda15808954fb29b0f105ed65f1 upstream.

syzkaller with KASAN reported an out-of-bounds read in
asn1_ber_decoder().  It can be reproduced by the following command,
assuming CONFIG_X509_CERTIFICATE_PARSER=y and CONFIG_KASAN=y:

    keyctl add asymmetric desc $'\x30\x30' @s

The bug is that the length of an ASN.1 data value isn't validated in the
case where it is encoded using the short form, causing the decoder to
read past the end of the input buffer.  Fix it by validating the length.

The bug report was:

    BUG: KASAN: slab-out-of-bounds in asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
    Read of size 1 at addr ffff88003cccfa02 by task syz-executor0/6818

    CPU: 1 PID: 6818 Comm: syz-executor0 Not tainted 4.14.0-rc7-00008-g5f479447d983 #2
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
    Call Trace:
     __dump_stack lib/dump_stack.c:16 [inline]
     dump_stack+0xb3/0x10b lib/dump_stack.c:52
     print_address_description+0x79/0x2a0 mm/kasan/report.c:252
     kasan_report_error mm/kasan/report.c:351 [inline]
     kasan_report+0x236/0x340 mm/kasan/report.c:409
     __asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:427
     asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
     x509_cert_parse+0x1db/0x650 crypto/asymmetric_keys/x509_cert_parser.c:89
     x509_key_preparse+0x64/0x7a0 crypto/asymmetric_keys/x509_public_key.c:174
     asymmetric_key_preparse+0xcb/0x1a0 crypto/asymmetric_keys/asymmetric_type.c:388
     key_create_or_update+0x347/0xb20 security/keys/key.c:855
     SYSC_add_key security/keys/keyctl.c:122 [inline]
     SyS_add_key+0x1cd/0x340 security/keys/keyctl.c:62
     entry_SYSCALL_64_fastpath+0x1f/0xbe
    RIP: 0033:0x447c89
    RSP: 002b:00007fca7a5d3bd8 EFLAGS: 00000246 ORIG_RAX: 00000000000000f8
    RAX: ffffffffffffffda RBX: 00007fca7a5d46cc RCX: 0000000000447c89
    RDX: 0000000020006f4a RSI: 0000000020006000 RDI: 0000000020001ff5
    RBP: 0000000000000046 R08: fffffffffffffffd R09: 0000000000000000
    R10: 0000000000000002 R11: 0000000000000246 R12: 0000000000000000
    R13: 0000000000000000 R14: 00007fca7a5d49c0 R15: 00007fca7a5d4700

Fixes: 42d5ec27f873 ("X.509: Add an ASN.1 decoder")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: return full count in keyring_read() if buffer is too small

commit 3239b6f29bdfb4b0a2ba59df995fc9e6f4df7f1f upstream.

Commit e645016abc80 ("KEYS: fix writing past end of user-supplied buffer
in keyring_read()") made keyring_read() stop corrupting userspace memory
when the user-supplied buffer is too small. However it also made the
return value in that case be the short buffer size rather than the size
required, yet keyctl_read() is actually documented to return the size
required. Therefore, switch it over to the documented behavior.

Note that for now we continue to have it fill the short buffer, since it
did that before (pre-v3.13) and dump_key_tree_aux() in keyutils arguably
relies on it.

Fixes: e645016abc80 ("KEYS: fix writing past end of user-supplied buffer in keyring_read()")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: check MaxPathNameComponentLength != 0 before using it

commit f74bc7c6679200a4a83156bb89cbf6c229fe8ec0 upstream.

And fix tcon leak in error path.

Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: David Disseldorp <ddiss@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: Fix nested rwsem annotation for lockdep splat

commit 1f20f9ff57ca23b9f5502fca85ce3977e8496cb1 upstream.

syzkaller reported the lockdep splat due to the possible deadlock of
grp->list_mutex of each sequencer client object.  Actually this is
rather a false-positive report due to the missing nested lock
annotations.  The sequencer client may deliver the event directly to
another client which takes another own lock.

For addressing this issue, this patch replaces the simple down_read()
with down_read_nested().  As a lock subclass, the already existing
"hop" can be re-used, which indicates the depth of the call.

Reference: http://lkml.kernel.org/r/089e082686ac9b482e055c832617@google.com
Reported-by: syzbot <bot+7feb8de6b4d6bf810cf098bef942cc387e79d0ad@syzkaller.appspotmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: timer: Add missing mutex lock for compat ioctls

commit 79fb0518fec8c8b4ea7f1729f54f293724b3dbb0 upstream.

The races among ioctl and other operations were protected by the
commit af368027a49a ("ALSA: timer: Fix race among timer ioctls") and
later fixes, but one code path was forgotten in the scenario: the
32bit compat ioctl. As syzkaller recently spotted, a very similar
use-after-free may happen with the combination of compat ioctls.

The fix is simply to apply the same ioctl_lock to the compat_ioctl
callback, too.

Fixes: af368027a49a ("ALSA: timer: Fix race among timer ioctls")
Reference: http://lkml.kernel.org/r/089e082686ac9b482e055c832617@google.com
Reported-by: syzbot <bot+e5f3c9783e7048a74233054febbe9f1bdf54b6da@syzkaller.appspotmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ecryptfs: fix dereference of NULL user_key_payload

commit f66665c09ab489a11ca490d6a82df57cfc1bea3e upstream.

In eCryptfs, we failed to verify that the authentication token keys are
not revoked before dereferencing their payloads, which is problematic
because the payload of a revoked key is NULL. request_key() *does* skip
revoked keys, but there is still a window where the key can be revoked
before we acquire the key semaphore.

Fix it by updating ecryptfs_get_key_payload_data() to return
-EKEYREVOKED if the key payload is NULL. For completeness we check this
for "encrypted" keys as well as "user" keys, although encrypted keys
cannot be revoked currently.

Alternatively we could use key_validate(), but since we'll also need to
fix ecryptfs_get_key_payload_data() to validate the payload length, it
seems appropriate to just check the payload pointer.

Fixes: 237fead61998 ("[PATCH] ecryptfs: fs/Makefile and fs/Kconfig")
Reviewed-by: James Morris <james.l.morris@oracle.com>
Cc: Michael Halcrow <mhalcrow@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: fan53555: fix I2C device ids

commit fc1111b885437f374ed54aadda44d8b241ebd2a3 upstream.

The device tree nodes all correctly describe the regulators as
syr827 or syr828, but the I2C device id is currently set to the
wildcard value of syr82x in the driver.  This causes udev to fail
to match the driver module with the modalias data from sysfs.

Fix this by replacing the I2C device ids with ones that match the
device tree descriptions, with syr827 and syr828.  Tested on
Firefly rk3288 board.  The syr82x id was not used anywhere.

Fixes: e80c47bd738b (regulator: fan53555: Export I2C module alias information)
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipsec: Fix aborted xfrm policy dump crash

commit 1137b5e2529a8f5ca8ee709288ecba3e68044df2 upstream.

An independent security researcher, Mohamed Ghannam, has reported
this vulnerability to Beyond Security's SecuriTeam Secure Disclosure
program.

The xfrm_dump_policy_done function expects xfrm_dump_policy to
have been called at least once or it will crash. This can be
triggered if a dump fails because the target socket's receive
buffer is full.

This patch fixes it by using the cb->start mechanism to ensure that
the initialisation is always done regardless of the buffer situation.

Fixes: 12a169e7d8f4 ("ipsec: Put dumpers on the dump list")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: fix connect/disconnect edge cases

commit 51e13359cd5ea34acc62c90627603352956380af upstream.

If we try to connect while already connected/connecting, but
this fails, we set ssid_len=0 but leave current_bss hanging,
leading to errors.

Check all of this better, first of all ensuring that we can't
try to connect to a different SSID while connected/ing; ensure
that prev_bssid is set for re-association attempts even in the
case of the driver supporting the connect() method, and don't
reset ssid_len in the failure cases.

While at it, also reset ssid_len while disconnecting unless we
were connected and expect a disconnected event, and warn on a
successful connection without ssid_len being set.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: kvaser_usb: Ignore CMD_FLUSH_QUEUE_REPLY messages

commit e1d2d1329a5722dbecc9c278303fcc4aa01f8790 upstream.

To avoid kernel warning "Unhandled message (68)", ignore the
CMD_FLUSH_QUEUE_REPLY message for now.

As of Leaf v2 firmware version v4.1.844 (2017-02-15), flush tx queue is
synchronous. There is a capability bit indicating whether flushing tx
queue is synchronous or asynchronous.

A proper solution would be to query the device for capabilities. If the
synchronous tx flush capability bit is set, we should wait for
CMD_FLUSH_QUEUE_REPLY message, while flushing the tx queue.

Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>