#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
#include <dt-bindings/sound/apq8016-lpass.h>
-/*
- * GPIO name legend: proper name = the GPIO line is used as GPIO
- * NC = not connected (pin out but not routed from the chip to
- * anything the board)
- * "[PER]" = pin is muxed for [peripheral] (not GPIO)
- * LSEC = Low Speed External Connector
- * HSEC = High Speed External Connector
- *
- * Line names are taken from the schematic "DragonBoard410c"
- * dated monday, august 31, 2015. Page 5 in particular.
- *
- * For the lines routed to the external connectors the
- * lines are named after the 96Boards CE Specification 1.0,
- * Appendix "Expansion Connector Signal Description".
- *
- * When the 96Board naming of a line and the schematic name of
- * the same line are in conflict, the 96Board specification
- * takes precedence, which means that the external UART on the
- * LSEC is named UART0 while the schematic and SoC names this
- * UART3. This is only for the informational lines i.e. "[FOO]",
- * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
- * ones actually used for GPIO.
- */
-
/ {
aliases {
serial0 = &blsp1_uart2;
};
reserved-memory {
- ramoops@bff00000{
+ ramoops@bff00000 {
compatible = "ramoops";
reg = <0x0 0xbff00000 0x0 0x100000>;
};
};
- soc {
- pinctrl@1000000 {
- gpio-line-names =
- "[UART0_TX]", /* GPIO_0, LSEC pin 5 */
- "[UART0_RX]", /* GPIO_1, LSEC pin 7 */
- "[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
- "[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
- "[UART1_TX]", /* GPIO_4, LSEC pin 11 */
- "[UART1_RX]", /* GPIO_5, LSEC pin 13 */
- "[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
- "[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
- "[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
- "[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
- "[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
- "[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
- "GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
- "GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
- "[I2C3_SDA]", /* HSEC pin 38 */
- "[I2C3_SCL]", /* HSEC pin 36 */
- "[SPI0_MOSI]", /* LSEC pin 14 */
- "[SPI0_MISO]", /* LSEC pin 10 */
- "[SPI0_CS_N]", /* LSEC pin 12 */
- "[SPI0_CLK]", /* LSEC pin 8 */
- "HDMI_HPD_N", /* GPIO 20 */
- "USR_LED_1_CTRL",
- "[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
- "[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
- "GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
- "GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
- "[CSI0_MCLK]", /* HSEC pin 15 */
- "[CSI1_MCLK]", /* HSEC pin 17 */
- "GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
- "[I2C2_SDA]", /* HSEC pin 34 */
- "[I2C2_SCL]", /* HSEC pin 32 */
- "DSI2HDMI_INT_N",
- "DSI_SW_SEL_APQ",
- "GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
- "GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
- "GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
- "GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
- "FORCED_USB_BOOT",
- "SD_CARD_DET_N",
- "[WCSS_BT_SSBI]",
- "[WCSS_WLAN_DATA_2]", /* GPIO 40 */
- "[WCSS_WLAN_DATA_1]",
- "[WCSS_WLAN_DATA_0]",
- "[WCSS_WLAN_SET]",
- "[WCSS_WLAN_CLK]",
- "[WCSS_FM_SSBI]",
- "[WCSS_FM_SDI]",
- "[WCSS_BT_DAT_CTL]",
- "[WCSS_BT_DAT_STB]",
- "NC",
- "NC", /* GPIO 50 */
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 60 */
- "NC",
- "NC",
- "[CDC_PDM0_CLK]",
- "[CDC_PDM0_SYNC]",
- "[CDC_PDM0_TX0]",
- "[CDC_PDM0_RX0]",
- "[CDC_PDM0_RX1]",
- "[CDC_PDM0_RX2]",
- "GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
- "NC", /* GPIO 70 */
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 74 */
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "BOOT_CONFIG_0", /* GPIO 80 */
- "BOOT_CONFIG_1",
- "BOOT_CONFIG_2",
- "BOOT_CONFIG_3",
- "NC",
- "NC",
- "BOOT_CONFIG_5",
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 90 */
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 100 */
- "NC",
- "NC",
- "NC",
- "SSBI_GPS",
- "NC",
- "NC",
- "KEY_VOLP_N",
- "NC",
- "NC",
- "[LS_EXP_MI2S_WS]", /* GPIO 110 */
- "NC",
- "NC",
- "[LS_EXP_MI2S_SCK]",
- "[LS_EXP_MI2S_DATA0]",
- "GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
- "NC",
- "[DSI2HDMI_MI2S_WS]",
- "[DSI2HDMI_MI2S_SCK]",
- "[DSI2HDMI_MI2S_DATA0]",
- "USR_LED_2_CTRL", /* GPIO 120 */
- "SB_HS_ID";
- };
-
- dma@7884000 {
- status = "okay";
- };
-
- serial@78af000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp1_uart1_default>;
- pinctrl-1 = <&blsp1_uart1_sleep>;
- };
-
- serial@78b0000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp1_uart2_default>;
- pinctrl-1 = <&blsp1_uart2_sleep>;
- };
-
- i2c@78b6000 {
- /* On Low speed expansion */
- label = "LS-I2C0";
- status = "okay";
- };
-
- i2c@78b8000 {
- /* On High speed expansion */
- label = "HS-I2C2";
- status = "okay";
-
- adv_bridge: bridge@39 {
- status = "okay";
-
- compatible = "adi,adv7533";
- reg = <0x39>;
-
- interrupt-parent = <&msmgpio>;
- interrupts = <31 2>;
-
- adi,dsi-lanes = <4>;
- clocks = <&rpmcc RPM_SMD_BB_CLK2>;
- clock-names = "cec";
-
- pd-gpios = <&msmgpio 32 0>;
-
- avdd-supply = <&pm8916_l6>;
- v1p2-supply = <&pm8916_l6>;
- v3p3-supply = <&pm8916_l17>;
-
- pinctrl-names = "default","sleep";
- pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
- pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
- #sound-dai-cells = <1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7533_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7533_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
- };
-
- i2c@78ba000 {
- /* On Low speed expansion */
- label = "LS-I2C1";
- status = "okay";
- };
-
- spi@78b7000 {
- /* On High speed expansion */
- label = "HS-SPI1";
- status = "okay";
- };
-
- spi@78b9000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
- };
-
- sdhci@7824000 {
- vmmc-supply = <&pm8916_l8>;
- vqmmc-supply = <&pm8916_l5>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
- pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
- status = "okay";
- };
-
- sdhci@7864000 {
- vmmc-supply = <&pm8916_l11>;
- vqmmc-supply = <&pm8916_l12>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
- pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
-
- cd-gpios = <&msmgpio 38 0x1>;
- status = "okay";
- };
-
- usb@78d9000 {
- extcon = <&usb_id>, <&usb_id>;
- status = "okay";
- adp-disable;
- hnp-disable;
- srp-disable;
- pinctrl-names = "default", "device";
- pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
- pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
- ulpi {
- phy {
- v1p8-supply = <&pm8916_l7>;
- v3p3-supply = <&pm8916_l13>;
- extcon = <&usb_id>;
- };
- };
- };
-
- lpass@7708000 {
- status = "okay";
- };
-
- mdss@1a00000 {
- dsi@1a98000 {
- vdda-supply = <&pm8916_l2>;
- vddio-supply = <&pm8916_l6>;
-
- ports {
- port@1 {
- endpoint {
- remote-endpoint = <&adv7533_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
- };
-
- dsi-phy@1a98300 {
- vddio-supply = <&pm8916_l6>;
- };
- };
-
- /*
- Internal Codec
- playback - Primary MI2S
- capture - Ter MI2S
-
- External Primary:
- playback - secondary MI2S
- capture - Quat MI2S
-
- External Secondary:
- playback - Quat MI2S
- capture - Quat MI2S
-
- */
-
- sound: sound@7702000 {
- status = "okay";
- pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
- pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
- pinctrl-names = "default", "sleep";
- qcom,model = "DB410c";
- qcom,audio-routing =
- "AMIC2", "MIC BIAS Internal2",
- "AMIC3", "MIC BIAS External1";
-
- external-dai-link@0 {
- link-name = "ADV7533";
- cpu {
- sound-dai = <&lpass MI2S_QUATERNARY>;
- };
- codec {
- sound-dai = <&adv_bridge 0>;
- };
- };
-
- internal-codec-playback-dai-link@0 {
- link-name = "WCD";
- cpu {
- sound-dai = <&lpass MI2S_PRIMARY>;
- };
- codec {
- sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
- };
- };
-
- internal-codec-capture-dai-link@0 {
- link-name = "WCD-Capture";
- cpu {
- sound-dai = <&lpass MI2S_TERTIARY>;
- };
- codec {
- sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
- };
- };
- };
-
- spmi@200f000 {
- pm8916@0 {
- gpios@c000 {
- gpio-line-names =
- "USR_LED_3_CTRL",
- "USR_LED_4_CTRL",
- "USB_HUB_RESET_N_PM",
- "USB_SW_SEL_PM";
- };
- mpps@a000 {
- gpio-line-names =
- "VDD_PX_BIAS",
- "WLAN_LED_CTRL",
- "BT_LED_CTRL",
- "GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
- };
- };
- };
-
- wcnss@a21b000 {
- status = "okay";
- };
-
- tpiu@820000 { status = "okay"; };
- funnel@821000 { status = "okay"; };
- replicator@824000 { status = "okay"; };
- etf@825000 { status = "okay"; };
- etr@826000 { status = "okay"; };
- funnel@841000 { status = "okay"; };
- debug@850000 { status = "okay"; };
- debug@852000 { status = "okay"; };
- debug@854000 { status = "okay"; };
- debug@856000 { status = "okay"; };
- etm@85c000 { status = "okay"; };
- etm@85d000 { status = "okay"; };
- etm@85e000 { status = "okay"; };
- etm@85f000 { status = "okay"; };
- cti@810000 { status = "okay"; };
- cti@811000 { status = "okay"; };
- cti@858000 { status = "okay"; };
- cti@859000 { status = "okay"; };
- cti@85a000 { status = "okay"; };
- cti@85b000 { status = "okay"; };
- };
-
usb2513 {
compatible = "smsc,usb3503";
reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
};
};
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp_i2c2 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C0";
+};
+
+&blsp_i2c4 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-I2C2";
+
+ adv_bridge: bridge@39 {
+ status = "okay";
+
+ compatible = "adi,adv7533";
+ reg = <0x39>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+
+ adi,dsi-lanes = <4>;
+ clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+ clock-names = "cec";
+
+ pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
+
+ avdd-supply = <&pm8916_l6>;
+ v1p2-supply = <&pm8916_l6>;
+ v3p3-supply = <&pm8916_l17>;
+
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+ pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+ #sound-dai-cells = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7533_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7533_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&blsp_i2c6 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C1";
+};
+
+&blsp_spi3 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-SPI1";
+};
+
+&blsp_spi5 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-SPI0";
+};
+
+&blsp1_uart1 {
+ status = "okay";
+ label = "LS-UART0";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ pinctrl-1 = <&blsp1_uart1_sleep>;
+};
+
+&blsp1_uart2 {
+ status = "okay";
+ label = "LS-UART1";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart2_default>;
+ pinctrl-1 = <&blsp1_uart2_sleep>;
+};
+
&camss {
status = "okay";
ports {
};
};
+&dsi0 {
+ vdda-supply = <&pm8916_l2>;
+ vddio-supply = <&pm8916_l6>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&adv7533_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+};
+
+&dsi_phy0 {
+ vddio-supply = <&pm8916_l6>;
+};
+
+&lpass {
+ status = "okay";
+};
+
+&pronto {
+ status = "okay";
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8916_l8>;
+ vqmmc-supply = <&pm8916_l5>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+ pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ vmmc-supply = <&pm8916_l11>;
+ vqmmc-supply = <&pm8916_l12>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+ cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+};
+
+&sound {
+ status = "okay";
+
+ pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
+ pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
+ pinctrl-names = "default", "sleep";
+ qcom,model = "DB410c";
+ qcom,audio-routing =
+ "AMIC2", "MIC BIAS Internal2",
+ "AMIC3", "MIC BIAS External1";
+
+ external-dai-link@0 {
+ link-name = "ADV7533";
+ cpu {
+ sound-dai = <&lpass MI2S_QUATERNARY>;
+ };
+ codec {
+ sound-dai = <&adv_bridge 0>;
+ };
+ };
+
+ internal-codec-playback-dai-link@0 {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+ };
+ };
+
+ internal-codec-capture-dai-link@0 {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+ };
+ };
+};
+
&spmi_bus {
pm8916_0: pm8916@0 {
pon@800 {
};
};
+&usb {
+ status = "okay";
+ extcon = <&usb_id>, <&usb_id>;
+ adp-disable;
+ hnp-disable;
+ srp-disable;
+
+ pinctrl-names = "default", "device";
+ pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+ pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+};
+
+&usb_hs_phy {
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+ extcon = <&usb_id>;
+};
+
&wcd_codec {
clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
clock-names = "mclk";
qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
};
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&tpiu { status = "okay"; };
+
&smd_rpm_regulators {
vdd_l1_l2_l3-supply = <&pm8916_s3>;
vdd_l4_l5_l6-supply = <&pm8916_s4>;
drive-strength = <16>;
};
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (pin out but not routed from the chip to
+ * anything the board)
+ * "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "DragonBoard410c"
+ * dated monday, august 31, 2015. Page 5 in particular.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+
&msmgpio {
+ gpio-line-names =
+ "[UART0_TX]", /* GPIO_0, LSEC pin 5 */
+ "[UART0_RX]", /* GPIO_1, LSEC pin 7 */
+ "[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
+ "[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
+ "[UART1_TX]", /* GPIO_4, LSEC pin 11 */
+ "[UART1_RX]", /* GPIO_5, LSEC pin 13 */
+ "[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
+ "[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
+ "[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
+ "[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
+ "[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
+ "[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
+ "GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
+ "GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
+ "[I2C3_SDA]", /* HSEC pin 38 */
+ "[I2C3_SCL]", /* HSEC pin 36 */
+ "[SPI0_MOSI]", /* LSEC pin 14 */
+ "[SPI0_MISO]", /* LSEC pin 10 */
+ "[SPI0_CS_N]", /* LSEC pin 12 */
+ "[SPI0_CLK]", /* LSEC pin 8 */
+ "HDMI_HPD_N", /* GPIO 20 */
+ "USR_LED_1_CTRL",
+ "[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
+ "[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
+ "GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
+ "GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
+ "[CSI0_MCLK]", /* HSEC pin 15 */
+ "[CSI1_MCLK]", /* HSEC pin 17 */
+ "GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
+ "[I2C2_SDA]", /* HSEC pin 34 */
+ "[I2C2_SCL]", /* HSEC pin 32 */
+ "DSI2HDMI_INT_N",
+ "DSI_SW_SEL_APQ",
+ "GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
+ "GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
+ "GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
+ "GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
+ "FORCED_USB_BOOT",
+ "SD_CARD_DET_N",
+ "[WCSS_BT_SSBI]",
+ "[WCSS_WLAN_DATA_2]", /* GPIO 40 */
+ "[WCSS_WLAN_DATA_1]",
+ "[WCSS_WLAN_DATA_0]",
+ "[WCSS_WLAN_SET]",
+ "[WCSS_WLAN_CLK]",
+ "[WCSS_FM_SSBI]",
+ "[WCSS_FM_SDI]",
+ "[WCSS_BT_DAT_CTL]",
+ "[WCSS_BT_DAT_STB]",
+ "NC",
+ "NC", /* GPIO 50 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 60 */
+ "NC",
+ "NC",
+ "[CDC_PDM0_CLK]",
+ "[CDC_PDM0_SYNC]",
+ "[CDC_PDM0_TX0]",
+ "[CDC_PDM0_RX0]",
+ "[CDC_PDM0_RX1]",
+ "[CDC_PDM0_RX2]",
+ "GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
+ "NC", /* GPIO 70 */
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 74 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "BOOT_CONFIG_0", /* GPIO 80 */
+ "BOOT_CONFIG_1",
+ "BOOT_CONFIG_2",
+ "BOOT_CONFIG_3",
+ "NC",
+ "NC",
+ "BOOT_CONFIG_5",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 90 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 100 */
+ "NC",
+ "NC",
+ "NC",
+ "SSBI_GPS",
+ "NC",
+ "NC",
+ "KEY_VOLP_N",
+ "NC",
+ "NC",
+ "[LS_EXP_MI2S_WS]", /* GPIO 110 */
+ "NC",
+ "NC",
+ "[LS_EXP_MI2S_SCK]",
+ "[LS_EXP_MI2S_DATA0]",
+ "GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
+ "NC",
+ "[DSI2HDMI_MI2S_WS]",
+ "[DSI2HDMI_MI2S_SCK]",
+ "[DSI2HDMI_MI2S_DATA0]",
+ "USR_LED_2_CTRL", /* GPIO 120 */
+ "SB_HS_ID";
+
msmgpio_leds: msmgpio-leds {
pins = "gpio21", "gpio120";
function = "gpio";
};
&pm8916_gpios {
+ gpio-line-names =
+ "USR_LED_3_CTRL",
+ "USR_LED_4_CTRL",
+ "USB_HUB_RESET_N_PM",
+ "USB_SW_SEL_PM";
+
usb_hub_reset_pm: usb-hub-reset-pm {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
};
&pm8916_mpps {
+ gpio-line-names =
+ "VDD_PX_BIAS",
+ "WLAN_LED_CTRL",
+ "BT_LED_CTRL",
+ "GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
+
pinctrl-names = "default";
pinctrl-0 = <&ls_exp_gpio_f>;
projects / linux.git / commitdiff